ISO 13485 Requirements for Suppliers: What Device Customers Pass Down
Reviewed by Aaron Lyon, President of A.P. Lyon and former Director of Quality Assurance and International Regulatory, with more than 30 years in medical device quality. Last reviewed November 18, 2026.
If you run an ISO 9001 machine shop, molding operation or contract manufacturer, a new medical device customer can feel like a different world. The purchase order arrives with a quality agreement, a change notification clause, traceability requirements and a request to schedule a supplier audit. None of it appears in ISO 9001, and you may be told you need to be "13485 compliant" even though nobody asks you to get certified.
This guide explains where those requests come from, which ISO 13485:2016 clauses drive them, and what an ISO 9001 supplier needs to add to its quality system to meet them. It is written for component and process suppliers, not for the device manufacturer itself.
Does FDA regulate component suppliers?
Usually not directly. FDA's Quality Management System Regulation, 21 CFR Part 820, says that its provisions do not apply to manufacturers of components or parts of finished devices, but that such manufacturers are encouraged to consider its provisions as appropriate (21 CFR 820.1(a)(2)).
The regulation defines a component broadly: any raw material, substance, piece, part, software, firmware, labeling or assembly intended to be included as part of the finished, packaged and labeled device (21 CFR 820.3). So a machined screw, a molded housing, a cable assembly and a printed label can all be components.
What does apply is the requirement on your customer. Since the QMSR took effect, a device manufacturer must document a quality management system that complies with the applicable requirements of ISO 13485 (21 CFR 820.10(a)). ISO 13485 makes the manufacturer responsible for what it buys and for processes it outsources. The manufacturer cannot meet those clauses without your help, so the requirements are written into your purchase orders and agreements. That is the "flow-down."
The ISO 13485 clauses that reach suppliers
These are the clauses that most often turn into supplier requirements. Each summary below is in our own words.
Clause 4.1.5, outsourced processes. When the manufacturer outsources a process that affects product conformity, it keeps responsibility for it and must monitor and control it in proportion to risk and to the supplier's ability to meet requirements. The controls must include a written quality agreement. If you plate, heat treat, clean, sterilize or assemble for a device maker, your work is often treated as an outsourced process.
Clauses 7.4.1 and 7.4.3, supplier evaluation and verification. The manufacturer selects and monitors suppliers on their ability to meet requirements, their performance and the effect of the purchased product on device quality, in proportion to the risk of the device. Expect a questionnaire, scorecards and periodic re-evaluation.
Clause 7.4.2, purchasing information. Purchasing information includes, as applicable, a written agreement that the supplier notifies the manufacturer of changes to the purchased product before implementing changes that affect its ability to meet purchase requirements. This is the source of the change notification clause.
Clauses 7.5.9.1 and 7.5.9.2, traceability. The manufacturer defines how far traceability goes, according to its regulations. For implantable devices, the records must include components, materials and work environment conditions that could affect safety and performance. FDA also applies 7.5.9.2 to devices that support or sustain life (21 CFR 820.10(d)). Those records live partly in your shop.
Clause 7.5.2, product cleanliness. Cleanliness or contamination control requirements must be documented in specific cases, including when process agents must be removed from the product. Cutting fluid, mold release and polishing compound are process agents.
Clause 7.5.6, process validation. Processes whose output is not or cannot be fully verified must be validated, with acceptance criteria, a rationale for sample size and criteria for revalidation. Welding, molding, cleaning and passivation are common examples at suppliers.
Clause 7.5.10, customer property. Customer tooling and material must be identified, verified, protected and safeguarded, and any loss, damage or unsuitability reported to the customer.
Clause 8.2.6, monitoring and measurement of product. Evidence of conformity is kept and the person authorizing release is recorded. For implantable devices, the identity of each person who performs an inspection or test is recorded.
Clauses 8.3.1 to 8.3.4, nonconforming product. A concession needs justification, approval and an identified authorizer, and the evaluation of a nonconformity includes deciding whether to notify any responsible external party. For a supplier, that usually means the customer must approve before any nonconforming part ships.
Clause 4.2.5, records. Records are kept at least for the lifetime of the device as the manufacturer defines it, or as regulations require, but not less than two years from release. Your customer will ask you to keep lot records that long.
What ISO 9001 already gives you
Most of the foundations are already in an ISO 9001:2026 system. Clause 8.2.3 requires you to review requirements before committing to supply. Clause 8.5.2 covers identification and traceability where it is required, and customer property. Clause 8.5.6 requires changes to production to be reviewed and controlled. Clause 8.6 says products are not released until planned checks are complete, unless a relevant authority and, where applicable, the customer approve. Clause 8.7 controls nonconforming outputs, including informing the customer and acceptance under concession.
The gap is not that ISO 9001 is weak. It is that ISO 9001 leaves many decisions to you, while a device customer needs those decisions made in a specific way and written down. ISO 9001 lets you decide whether a change needs customer notice. A device customer needs a written promise that it will hear about the change before you make it.
The gaps device customers find most often
When device makers audit ISO 9001 suppliers, the same findings come up again and again:
No written change notification process. The shop changed a coolant, a plating house or a mold insert, and the customer found out from a failed incoming inspection.
Traceability stops at the purchase order. The shop can say which purchase order a part shipped against, but not which bar stock heat, which mold cavity or which inspector.
Nonconforming product shipped on an internal deviation. The shop's material review board accepted a minor dimension, and the customer was never asked.
Cleanliness is "clean and free of oil" on the drawing and nothing else. There is no defined cleaning process, no check that process agents are removed, and no control of contaminated parts.
Records discarded on the shop's normal schedule. The customer's device has a ten-year life, but the shop kept travelers for three years.
No signed quality agreement. The commercial terms exist, but nobody agreed who validates the process, who approves changes or how fast a nonconformance is reported.
Every one of these is fixable with procedures and records, not with a new certificate.
Do you need ISO 13485 certification?
Usually not. Some customers prefer or require it for suppliers of critical components, and some contract manufacturers who build finished devices choose it. For most component suppliers, device customers accept ISO 9001 certification plus evidence that the flow-down requirements are met. Check the customer's supplier quality manual or purchase order terms, and ask. If the customer requires certification, a full ISO 13485 system is the right path. If it does not, adding a device-customer layer to your ISO 9001 system is faster and keeps one system rather than two.
What to add to an ISO 9001 system
A practical device-customer layer has five procedures and a few records:
Contract review for device customers. Before you accept a quote or order, find the device-specific requirements: the quality agreement, change notice terms, traceability level, cleanliness specification, record retention period and whether the part goes into an implantable or life-sustaining device. Record them so the shop floor sees them.
Customer change notification. Screen every engineering change for effect on device-customer parts, notify the customer before implementation, get approval where the agreement requires it, and pass the same requirement to your own sub-tier suppliers.
Component traceability. Define a standard level for all device parts and a full level for implant and life-sustaining parts, then record material lots, special process lots, equipment and cavity, inspectors and shipments on one lot record.
Product cleanliness and process agent removal. Set cleanliness requirements from the customer specification, validate the cleaning process where its output is not fully verified, and control contaminated product.
Customer concession and nonconformance notification. No nonconforming part ships without written customer approval, and the customer is told promptly when a problem is found after shipment.
Add a signed quality agreement, a certificate of conformance with each shipment, and a checklist to prepare for customer audits.
A worked example: a machined bone screw blank
A machine shop with ISO 9001 certification wins an order for titanium screw blanks from an orthopedic device company. The purchase order references a quality agreement and a cleanliness specification.
Contract review. The quoting team sees that the part is for an implantable device. It sets Full traceability, records the record retention period in the agreement, and flags the cleanliness specification for the manufacturing engineer.
Quality agreement. The shop and the customer complete the responsibilities table: the shop validates its cleaning process, sends a certificate of conformance with each lot, gives advance notice of changes and keeps records for the agreed period. The customer approves first articles and owns the device labeling.
Production. Each lot record lists the bar stock heat number and certificate, the machine and program, the cleaning batch, the clean area monitoring record for that day, and the name of each inspector.
A change. Six months later the shop wants to change its cutting fluid. That is a process agent that contacts the part, so it is a notifiable change. The shop sends a change notice with comparison cleaning data before switching and waits for the customer's written approval.
A nonconformance. One lot has a thread length 0.05 mm over tolerance. The shop does not ship it on an internal deviation. It sends a concession request, the customer's engineer approves it in writing for that lot only, and the certificate of conformance references the concession.
None of these steps needed ISO 13485 certification. Each needed a defined procedure and a record.
How the A.P. Lyon supplier pack fits
The Supplying the Medical Device Industry supplier pack has the five procedures above, six forms (quality agreement, change notification, lot traceability record, certificate of conformance, concession request and customer audit readiness checklist) and a requirements matrix that maps each ISO 13485 clause a customer may pass down to the procedure that meets it. It adds to the ISO 9001 QMS Complete system and refers to its document numbers. If you use another ISO 9001 system, the cross-reference table has a column for your own numbers.
Related reading: Supplier Quality Agreement for Medical Device Components and Change Notification: What Medical Device Customers Expect from Suppliers.
Frequently asked questions
Does 21 CFR Part 820 apply to my machine shop?
Not directly if you make components or parts. 21 CFR 820.1(a)(2) says the regulation does not apply to manufacturers of components or parts of finished devices, but encourages them to consider its provisions. Your device customer is covered, and it passes requirements to you by contract.
Which ISO 13485 clause requires change notification from suppliers?
Clause 7.4.2. Purchasing information includes, as applicable, a written agreement that the supplier notifies the manufacturer of changes to the purchased product before implementing changes that affect its ability to meet purchase requirements.
How long must a supplier keep records for a device customer?
As long as the quality agreement says. ISO 13485 clause 4.2.5 requires the manufacturer to keep records at least for the device lifetime it defines, or as regulations require, and not less than two years from release, so customers usually ask suppliers for the same period.
Building a complete quality system? Build Your QMS lets you choose ISO 13485 + FDA QMSR, Dual-Standard or ISO 9001:2026 procedures in one place, and applies volume discounts automatically: 20% off 5–9 procedures, 35% off 10–19, 50% off 20–39 and 60% off 40 or more.
Not sure where your quality system stands? Take the free QMS gap check: about 20 questions, an instant report of your gaps by clause, and the procedures that close each one.



Comments